Texas Fire Extinguisher Rules | TAC Chapter 34.500

TITLE 28 INSURANCE - PART 1 TEXAS DEPARTMENT OF INSURANCE - CHAPTER 34 STATE FIRE MARSHAL - SUBCHAPTER E FIRE EXTINGUISHER RULES

Rule §34.501 - Purpose - The purpose of this subchapter is to regulate the business of leasing, renting, selling, installing, and servicing of portable fire extinguishers and the planning, certifying, installing, or servicing of fixed fire extinguisher systems and to prohibit portable fire extinguishers, fixed fire extinguisher systems, and extinguisher equipment not listed by a testing laboratory approved by the commissioner in the interests of protecting and preserving lives and property under Insurance Code Chapter 6001.

Rule §34.502 - Title - These sections of this subchapter shall be known and may be cited as the extinguisher rules and shall be administered by and through the state fire marshal.

Rule §34.503 - Applicability of Subchapter - This subchapter shall apply to all firms and persons engaged in the business of leasing, renting, selling, installing, and servicing of portable fire extinguishers and the planning, certifying, installing, or servicing of fixed fire extinguisher systems and not to the general public.

Rule §34.504 - Exceptions - The exceptions of Insurance Code §6001.156 are applicable to the sections of this subchapter.

Rule §34.505 - Notices - Notice by the state fire marshal and required by any provisions of the statutes or of this subchapter must be given by personal service or mailed, postage prepaid, to the person's residence or business address as it appears on the records in the Office of the State Fire Marshal.

Rule §34.506 - Definitions - The following words and terms, when used in this subchapter, have the following meanings, unless the context clearly indicates otherwise.

(1) Apprentice--A person to whom a permit has been issued by the state fire marshal to perform various acts of service or installation while under the direct supervision of a person working for the same firm and holding a valid fire extinguisher service license to perform such acts.

(2) Business--The planning, certifying, installing, leasing, renting, selling, or servicing of portable fire extinguishers or fixed fire extinguisher systems.

(3) Certificate--The certificate of registration issued by the state fire marshal.

(4) Certify--To attest to the proper planning, installing, or servicing of portables and systems by attaching a completed service tag or other form required by a governmental authority.

(5) Commissioner--The commissioner of insurance.

(6) Department--The Texas Department of Insurance.

(7) DOT Specification Fire Extinguisher Cylinder--All fire extinguisher cylinders manufactured, tested and stamped with the specification number as required by the United States Department of Transportation.

(8) DOT Nonspecification Fire Extinguisher Cylinder--All fire extinguisher cylinders manufactured and tested but not stamped with a specification number as required by the United States Department of Transportation. These cylinders may be marked by a label with the words "Meets DOT Requirements."

(9) Installation--The initial placement of a portable or fixed fire extinguisher system or an extension or alteration after initial placement.

(10) License--The license issued by the state fire marshal to an employee of a registered firm.

(11) NFPA--The National Fire Protection Association, Inc., a nationally recognized standards-making organization.

(12) NICET--National Institute for the Certification in Engineering Technologies.

(13) Outsource testing service--The testing service selected by the state fire marshal to administer certain designated qualifying tests for licenses under this subchapter.

(14) Person--A natural person.

(15) Plan--To lay out, detail, draw, calculate, devise, or arrange an assembly of detection or suppression devices and appurtenances in accordance with either fire protection standards adopted in this subchapter or specifications specially designed by a Texas registered professional engineer acting solely in his professional capacity.

(16) Registered firm--A person, partnership, corporation, or association holding a current certificate of registration.

(17) Shop--A facility, whether at a specific location or in a mobile unit, of a registered firm where servicing, repairing, or hydrostatic testing is performed and where parts and equipment, which are required by this subchapter or in the adopted standards, are maintained.

(18) Test--The act of subjecting a portable or fixed system to any procedure necessary to determine whether it is properly installed or operates correctly.

(19) Direct supervision--The oversight by a licensee of the services performed by another licensee or permittee. The licensee, performing the direct supervision at the shop, must be present at all times on the premises where the supervised licensee or permittee is performing the service. When not at the shop, the individual being supervised must be within sight of the licensee performing the direct supervision when installing or servicing portable fire extinguishers or pre-engineered fixed fire extinguisher systems. The licensee performing the direct supervision of an engineered fixed fire extinguisher system is not required to be on-site at all times when the installation is performed.

Rule §34.507 - Adopted Standards - The Commissioner adopts by reference in their entirety, except as noted, the following copyrighted standards and recommendations in this subchapter. If a standard refers to a provision in a specific edition of another standard, the provision is applicable only if it does not conflict with the adopted standard shown in this section. The standards are published by and available from the National Fire Protection Association Inc. (NFPA) on the NFPA website at www.nfpa.org.

(1) NFPA 10-2018, Standard for Portable Fire Extinguishers.

(2) NFPA 11-2016, Standard for Low, Medium, and High-Expansion Foam and Combined Agent Systems.

(3) NFPA 12-2018, Standard on Carbon Dioxide Extinguishing Systems.

(4) NFPA 12A-2018, Standard on Halon 1301 Fire Extinguishing Systems.

(5) NFPA 15-2017, Standard for Water Spray Fixed Systems for Fire Protection.

(6) NFPA 16-2019, Standard for the Installation of Foam-Water Sprinkler and Foam-Water Spray Systems.

(7) NFPA 17-2021, Standard for Dry Chemical Extinguishing Systems.

(8) NFPA 17A-2021, Standard for Wet Chemical Extinguishing Systems.

(9) NFPA 18-2021, Standard on Wetting Agents.

(10) NFPA 25-2020, Standard for the Inspection, Testing, and Maintenance of Water-Based Fire Protection Systems.

(11) NFPA 33-2018, Standard for Spray Application Using Flammable or Combustible Materials.

(12) NFPA 96-2021, Standard for Ventilation Control and Fire Protection of Commercial Cooking Operations.

(13) NFPA 2001-2018, Standard on Clean Agent Fire Extinguishing Systems.

(14) NFPA 2010-2020, Standard for Fixed Aerosol Fire-Extinguishing Systems.

Rule §34.508 - Approved Testing Laboratories - The commissioner approves an organization as an approved testing laboratory which lists equipment and appurtenances for use in compliance with standards adopted in §34.507 of this title (relating to Adopted Standards) if the organization meets the requirements of an approved testing laboratory in accordance with Subchapter D of this title (relating to Testing Laboratory Rules).

Rule §34.509 - Approved Certification Organization - The commissioner approves the National Institute for Certification in Engineering Technologies (NICET) as a testing standards organization for testing license applicants.

Rule §34.510 - Certificates of Registration - (a) Required. Each firm and each branch office engaged in the business must obtain a certificate of registration from the state fire marshal.

(b) Properly equipped licensed person. Before engaging in the business, each registered firm must have at least one licensed person who must be properly equipped to perform the act or acts authorized by its certificate.

(c) Types of certificates. The business activities authorized by the certificate are limited to the business activities authorized under the license of its employees. A separate Type C registration is required to engage in the business of hydrostatic testing of U.S. Department of Transportation (U.S. DOT) specification fire extinguisher cylinders.

(d) Business location. Each registered firm must maintain a specific business location, and the business location must be indicated on the certificate. The business location must be a physical address, not a mailing address or P.O. Box.

(e) Shop. A registered firm must establish and maintain a shop, whether at a specific business location or in a mobile unit designed so that servicing, repairing, or hydrostatic testing can be performed. The shop must be adequately equipped to service or test all fire extinguishers or systems the registered firm installs and services. At a minimum, a firm must maintain the following:

(1) a copy of the most recently adopted edition of NFPA 10;

(2) a copy of the most recently adopted Insurance Code Chapter 6001 and this chapter;

(3) a list of manufacturers or types of portable extinguishers serviced with their respective manuals or part lists;

(4) portable scale to accurately measure extinguisher gross weights;

(5) seals or tamper indicators;

(6) temporary fire extinguishers replacements;

(7) if performing annual maintenance on carbon dioxide extinguishers, at a minimum, the following additional items are required:

(A) conductivity tester; and

(B) conductivity test label;

(8) if performing internal maintenance for portable extinguishers, a written notice must be kept on file indicating the registered firm performing the maintenance or, at a minimum, the following additional items are required:

(A) appropriate tools to remove and reinstall a valve head;

(B) charging adapters;

(C) Teflon tape, silicone grease, solvent, or other lubricant used;

(D) supply of spare parts for respective manufacturers and type of fire extinguishers serviced;

(E) appropriate recharge agents;

(F) agent fill funnels;

(G) light designed to be used for internal inspections;

(H) dry chemical closed recovery system or sufficient new dry chemical;

(I) leak test equipment;

(J) dry nitrogen cylinders, regulator and calibrated gauges for pressurizing cylinders;

(K) verification collar rings; and

(L) six-year maintenance labels.

(9) if performing hydrostatic testing for portable extinguishers, a written notice must be kept on file indicating the registered firm performing the test or, at a minimum, the following additional items are required:

(A) working hydrostatic test pump with flexible connection, check valves, and fittings;

(B) protective cage or barrier;

(C) calibrated gauges;

(D) drying equipment;

(E) hydrostatic test log; and

(F) hydrostatic test labels;

(10) if performing maintenance for U.S. DOT specification portable fire extinguishers, a written notice must be kept on file indicating the registered firm that would perform the hydrostatic test when required or, at a minimum, the following additional items are required:

(A) a current Type C registration issued by the State Fire Marshal's Office; and

(B) verification of registration through the U.S. DOT;

(11) if installing or servicing a fixed fire extinguisher system, at a minimum, the following additional items are required:

(A) a copy of the latest adopted edition of applicable NFPA standards with respect to the type of system installed or serviced;

(B) applicable manufacturer's service manuals for the type of system; and

(C) any special tools or parts as required by the manufacturer's manual.

(f) Business vehicles. All vehicles used regularly in installation, service, maintenance, testing, or certification activities must prominently display the company name, telephone number, and certificate of registration number. The numbers and letters must be at least one inch in height and permanently affixed or magnetically attached to each side of the vehicle in a color contrasting with the background color of the vehicle. The certificate-of-registration number must be designated in the following format: TX ECR-number. A business vehicle must be adequately equipped for the type of service that is being provided.

(g) Branch office initial certificate of registration fees and expiration dates. The initial fee for a branch office certificate of registration is $100 and is not prorated. Branch office certificates of registration expire and renew on the same date as the certificate of registration for the registered firm's main office.

(h) Change of ownership.

(1) The total change of a firm's ownership invalidates the current certificate. To ensure continuance of the business, the new owners must submit an application for a new certificate to the state fire marshal 14 days before the change.

(2) A partial change in a firm's ownership will require a revised certificate if it affects the firm's name, location, or mailing address.

(i) Change of corporate officers. Any change of corporate officers must be reported in writing to the state fire marshal within 14 days. This change does not require an application for a new or revised certificate.

(j) Duplicate certificates. A certificate holder must obtain a duplicate certificate from the state fire marshal to replace a lost or destroyed certificate. The certificate holder must submit written notification of the loss or destruction without delay, accompanied by the required fee.

(k) Revised certificates. The change of a firm's name, location, or mailing address requires a revised certificate. Within 14 days after the change requiring the revision, the registered firm must submit written notification of the necessary change accompanied by the required fee to the State Fire Marshal's Office.

(l) Nontransferable. A certificate is neither temporarily nor permanently transferable from one firm to another.

(m) Initial alignment of the expiration and renewal dates of existing branches. For branch offices in existence as of the effective date of this rule, branch office certificates of registration will expire and renew on the same date as the certificate of registration issued to the main office for that firm. All fees associated with the initial alignment of expiration and renewal dates for the branch office certificate of registration will prorate accordingly.

Rule §34.511 - Fire Extinguisher Licenses - 

(a) Types of licenses. Each license must be identified by type, which indicates the business activity authorized under the license.

(1) Type PL--For planning, supervising, certifying, installing, or servicing of all fixed systems other than pre-engineered systems. A system planning licensee may also perform, supervise, or certify the installation or servicing of all pre-engineered fixed systems and portable fire extinguishers.

(2) Type A--For certifying or servicing the installation of all fixed fire extinguisher systems, other than pre-engineered systems; or for installing, certifying, or servicing all pre-engineered fixed fire extinguisher systems, and certifying and servicing of portable extinguishers.

(3) Type B--For servicing, certifying, and low-pressure hydrostatic testing of portables.

(4) Type K--For installing, certifying, or servicing pre-engineered fixed fire extinguisher systems for the protection of cooking areas, and certifying and servicing portable extinguishers.

(b) Proof of licensure. A licensee must be able to show proof of licensure while engaged in the activities of the business.

(c) Duplicate license. A duplicate license must be obtained from the state fire marshal to replace a lost or destroyed license. The license holder or registered firm must submit written notification of the loss or destruction, accompanied by the required fee.

(d) Revised license. The change of a licensee's registered firm or mailing address requires a revised license. Within 14 days after the change requiring the revision, the license holder or registered firm must submit written notification of the necessary change accompanied by the required fee.

(e) Restrictions.

(1) A licensee must not engage in any act of the business unless employed by a registered firm and holding an unexpired license.

(2) A license is neither temporarily nor permanently transferable from one person to another.

(3) A registered firm must notify the state fire marshal within 14 days after termination of employment of a licensee.

(4) A Type A or Type K license will not be issued to an individual unless the individual has held an apprentice permit or a Type B license for at least six months or has held a license to service fixed extinguisher systems for at least six months from another state.

Rule §34.512 - Apprentice Permit - (a) Proof of licensure. A permit holder must be able to show proof of licensure while engaging in the business.

(b) Duplicate permit. A duplicate permit must be obtained from the state fire marshal to replace a lost or destroyed permit. The permit holder and his employer must submit written notification of the loss or destruction without delay, accompanied by the required fee.

(c) Revised permits. The change of a permittee's employer, home address, or mailing address requires a revised permit. Within 14 days after the change requiring the revision, the permit holder or registered firm must submit written notification to the State Fire Marshal's Office of the necessary change accompanied by the required fee.

(d) Nontransferable. A permit is neither temporarily nor permanently transferable from one person to another.

(e) Apprentice. An individual holding a current apprentice permit may, under the direct supervision of the licensee, assist in all respective services of the licensee; however, the licensee must sign all documents requiring the licensee's signature.

Rule §34.513 - Alteration of Certificates, Licenses, or Permits - Alteration of such documents renders them invalid and is the basis for administrative action pursuant to Insurance Code §6001.252.

Rule §34.514 - Applications - (a) Certificates of registration.

(1) Applications for certificates and branch office certificates must be submitted on forms provided by the state fire marshal and accompanied by all other information required by Insurance Code Chapter 6001, concerning Fire Extinguisher Service and Installation, and this subchapter. An application will not be deemed complete until all required forms and documents have been received in the State Fire Marshal's Office.

(2) Applications must be signed by the sole proprietor, or by each partner of a partnership, or by an officer of a corporation. For corporations, the application must be accompanied by the corporate charter of a Texas corporation, or, in the case of a foreign corporation, a copy of the Texas certificate of authority to do business. For applicants using an assumed name, the application must be accompanied by evidence of compliance with the Assumed Business or Professional Name Act, Texas Business and Commerce Code Chapter 71. The application must also include written authorization by the applicant permitting the state fire marshal or the state fire marshal's representative to enter, examine, and inspect any premises, building, room, or establishment used by the applicant while engaged in the business to determine compliance with the provisions of Insurance Code Chapter 6001 and this subchapter.

(3) For corporations, the application must also include the corporate taxpayer identification number, the charter number, and a copy of the corporation's current franchise tax certificate from the State Comptroller's Office showing it is in active status.

(4) Applications for Type C certificates must be accompanied by a copy of the U.S. DOT letter registering the applicant's facility and that issues a registration number to the facility.

(5) The applicant must comply with the following requirements concerning liability insurance.

(A) The state fire marshal will not issue a certificate of registration under this subchapter unless the applicant files a proof of liability insurance with the State Fire Marshal's Office. The insurance must include products and completed operations coverage.

(B) Each registered firm must maintain in force and on file in the State Fire Marshal's Office the certificate of insurance as required.

(C) Evidence of public liability insurance, as required by Insurance Code §6001.154, concerning Required Insurance Coverage for Registration Certificate, must be in the form of a certificate of insurance executed by an insurer authorized to do business in this state.

(D) If a certificate of registration is to be issued in the name of a corporation, the corporate name must be used on the applicable insurance forms. If the corporation is obtaining a certificate of registration in an assumed name, the insurance must be issued to the corporation doing business as (dba) the assumed name. Example: XYZ Corporation, dba XXX Extinguisher Service.

(E) Insurance issued for a partnership must be issued to the name of the partnership or to the names of all the individual partners.

(F) Insurance for a proprietorship must be issued to the individual owner. If an assumed name is used, the insurance must be issued to the individual doing business as "dba" followed by the assumed name. Example: William Jones, dba XXX Extinguisher Service.

(b) Fire extinguisher licenses.

(1) Original applications for a license from an employee of a firm engaged in the business must be submitted on forms provided by the state fire marshal and accompanied by a criminal history report from the Texas Department of Public Safety and all other information required by Insurance Code Chapter 6001 and this subchapter.

(2) For a natural person to be eligible for a Type A, K, or PL license, the natural person must start the application or registration process by submitting a formal request for a fingerprint service code by completing the fingerprinting process information required on the department's website at www.tdi.texas.gov/fire/fingerprinting-process.html. The requesting natural person must submit information necessary to complete the fingerprint service code request, including: the natural person's name, natural person's state of residence, natural person's email address, and license type the natural person is applying for.

(3) Applications for Type A and Type K licenses must be accompanied by a written statement from the certificate holder (employer) certifying that the applicant meets the minimum requirements of §34.511(e)(4) of this title (relating to Fire Extinguisher Licenses) and is competent to install or service fixed systems.

(4) Applications for Type PL licenses must be accompanied by one of the following documents to evidence technical qualifications for a license:

(A) proof of registration in Texas as a professional engineer; or

(B) a copy of the National Institute for Certification in Engineering Technologies (NICET) notification letter regarding the applicant's successful completion of examination requirements for certification at Level III for Special Hazard Systems Layout or Special Hazard Suppression Systems.

(5) All applications must indicate if the individual is an employee or agent of the registered firm.

(A) If the individual is an employee of the registered firm, the State Fire Marshal's Office may request from the registered firm verification of employment of the individual.

(B) If the individual is an agent of the fire extinguisher firm, the State Fire Marshal's Office may request that the firm provide a letter or other document acceptable to the State Fire Marshal's Office, issued by the firm's insurance company, verifying the policy number and that the acts of the individual are covered by the same insurance policy required by this subchapter to obtain the firm's registration. If required, the verifying document must be submitted to the State Fire Marshal's Office before a license will be issued or when there is a change in the licensee's registered firm. Unless otherwise required by the State Fire Marshal's Office, renewal of a license does not require insurance verification unless there has been a change in the insurance carrier.

(c) Complete application required for renewal. Renewal applications for certificates of registration and licenses must be submitted on forms provided by the state fire marshal and accompanied by a criminal history report obtained through the Texas Department of Public Safety and by all other information required by Insurance Code Chapter 6001 and this subchapter. An application will not be deemed complete until all required forms and documents have been received in the State Fire Marshal's Office.

(d) Timely filed. A license or registration expires at 12:00 midnight on the date printed on the license or registration. A renewal application and fee for license or registration must be postmarked on or before the date of expiration to be accepted as timely. If a renewal application is not complete but there has been no lapse in the required insurance, the applicant will have 30 days from the time the applicant is notified by the State Fire Marshal's Office of the deficiencies in the renewal application to submit any additional requirement. If an applicant fails to respond and correct all deficiencies in a renewal application within the 30-day period, a late fee may be charged.

(e) Requirements for applicants holding licenses from other states. An applicant holding a valid license in another state who desires to obtain a Texas license through reciprocity must submit the following documentation with the application in addition to all other information required by Insurance Code Chapter 6001 and this subchapter:

(1) a letter of certification from the licensing entity of another state certifying the applicant holds a valid license in that state; and

(2) additional information from the state detailing material content of any required examination used to qualify for license, including NFPA or other standards, if applicable.

(f) Apprentice permits. Each person employed as an apprentice by a firm engaged in the business must make application for a permit on a form provided by the state fire marshal, accompanied by a criminal history report from the Texas Department of Public Safety, and accompanied by the required application fee.

(1) For a natural person to be eligible for an apprentice permit, the natural person must start the application or registration process by submitting a formal request for a fingerprint service code by completing the fingerprinting process information required on the department's website at www.tdi.texas.gov/fire/fingerprinting-process.html, as specified in paragraph (2) of this subsection.

(2) The requesting natural person must submit information necessary to complete the fingerprint service code request, including: the natural person's name, natural person's state of residence, natural person's email address, and license type the natural person is applying for.

(g) Complete applications. The application form for a license or registration must be accompanied by the required application fee and must, within 180 days of receipt by the State Fire Marshal's Office of the initial application, be complete and accompanied by all other information required by Insurance Code Chapter 6001 and this subchapter, or a new application must be submitted, including all applicable fees.

Rule §34.515 - Fees - (a) Except for fees specified in subsection (d) of this section, all fees payable must be submitted by cashier's check or money order made payable to the Texas Department of Insurance or by online payment. Except for overpayments resulting from mistakes of law or fact, all fees are nonrefundable.

(b) Fees are as follows.

(1) Certificates of registration:

(A) initial fee--$450;

(B) renewal fee (for two years)--$600;

(C) renewal late fee (expired 1 day to 90 days)--$225 plus $50 for each branch office operated by the registered firm;

(D) renewal late fee (expired 91 days to two years)--$450 plus $100 for each branch office operated by the registered firm;

(E) branch office initial fee--$100;

(F) branch office renewal fee (for two years)--$200.

(2) Certificate of registration (Type C):

(A) initial fee--$250;

(B) renewal fee (for two years)--$300;

(C) renewal late fee (expired 1 day to 90 days)--$125;

(D) renewal late fee (expired 91 days to two years)--$250.

(3) Fire extinguisher license (Type A, B, and K):

(A) initial fee--$70;

(B) renewal fee (for two years)--$100;

(C) renewal late fee (expired 1 day to 90 days)--$35;

(D) renewal late fee (expired 91 days to two years)--$70.

(4) Fire extinguisher license (Type PL):

(A) initial fee--$70;

(B) renewal fee (for two years)--$100;

(C) renewal late fee (expired 1 day to 90 days)--$35;

(D) renewal late fee (expired 91 days to two years)--$70.

(5) Apprentice permit fee--$30.

(6) Change of address request--$0.

(7) Duplicate or revised certificates, licenses, permits, or other requested changes to certificates, licenses, or permits--$20.

(8) Initial test fee (if administered by the SFMO)--$20.

(9) Retest fee (if administered by the SFMO)--$20.

(c) Fees for tests administered by an outsource testing service are payable to the testing service in the amount and manner required by the testing service.

(d) Late fees are required of all certificate or license holders who fail to submit complete renewal applications before the expiration of the certificate or license.

Rule §34.516 - Tests - (a) Applicants for licenses are required to take a test and obtain a grade of at least 70 percent on the test. Tests may be supplemented by practical tests or demonstrations deemed necessary to determine the applicant's knowledge and ability. The test content, frequency, location, and outsource testing service must be designated by the state fire marshal.

(1) The Type B license test will include questions on the following:

(A) this subchapter and Insurance Code Chapter 6001; and

(B) installing and servicing of portables.

(2) The Type A license test will include questions on the following:

(A) this subchapter and Insurance Code Chapter 6001;

(B) installing and servicing of portables;

(C) fixed systems; and

(D) installing and servicing pre-engineered fixed fire extinguisher systems for the protection of cooking areas.

(3) The Type K license test will include questions on the following:

(A) this subchapter and Insurance Code Chapter 6001;

(B) installing and servicing of portables; and

(C) installing and servicing pre-engineered fixed fire extinguisher systems for the protection of cooking areas.

(4) The Type PL license test will include questions on the following:

(A) this subchapter and Insurance Code Chapter 6001; and

(B) a technically qualifying test to be conducted through NICET.

(b) The standards used in the tests will be adopted by the State Fire Marshal's Office.

(c) Examinees who fail any topic on the test must file a retest application accompanied by the required fee.

(d) A person whose license has been expired for two years or longer who makes application for a new license must take and pass another test. No test is required for a licensee whose license is renewed within two years of expiration.

(e) An examinee who is scheduled for a test to be conducted on a religious holy day by the State Fire Marshal's Office and who wishes to observe the religious holy day may request the rescheduling of the test to an alternate date.

(f) An applicant may only schedule each type of test three times within a twelve-month period.

(g) An applicant for a license must complete and submit all application requirements within one year of the successful completion of any test required for a license, except for testing conducted through NICET; otherwise, the test is voided and the individual will have to pass the test again.

Rule §34.517 - Installation and Service - (a) The following requirements are applicable to all portable extinguishers.

(1) Portable extinguishers must be installed, serviced, and maintained in compliance with the manufacturer's instructions and with the applicable standards adopted in this subchapter except when the installation or servicing complies with a standard that has been adopted by the political subdivision in which the system is installed.

(2) A service tag certifying the work the licensee performed must be securely attached to the portable extinguisher on completion of the work.

(3) When requested in writing by the owner, a portable fire extinguisher of the type described in subparagraphs (A), (B), or (C) of this paragraph may be serviced according to the requirement of this subchapter, regardless of whether it carries the label of approval or listing of a testing laboratory approved according to this subchapter.

(A) All portable fire extinguishers serviced according to the requirements of the United States Coast Guard and installed for use in foreign shipping vessels;

(B) all portable carbon dioxide fire extinguishers serviced according to the requirements of the United States Department of Transportation; or

(C) cartridge-actuated portable fire extinguishers used exclusively by employees of the firm owning the extinguishers.

(4) A licensee who services portable fire extinguishers according to paragraph (3) of this subsection, must comply with the following:

(A) The back of the service tag must be plainly marked with the words "No Listing Mark."

(B) All missing markings, code symbols, instructions, and information required by the applicable performance standard and fire test standard specified in §34.507(1) of this title (relating to Adopted Standards), except for the approving or listing mark of the testing laboratory, must be affixed to each extinguisher in the form of a label designated in the standard.

(b) The following requirements are applicable to all fixed fire extinguisher systems.

(1) Fixed systems must be planned, installed, and serviced in compliance with the manufacturer's installation manuals and specifications or the applicable standards adopted in this subchapter, except when the installation or servicing complies with a standard that has been adopted by the political subdivision in which the system is installed.

(2) On completion of the installation of a pre-engineered fixed fire extinguisher system, a licensee authorized to certify pre-engineered fixed fire extinguishing systems under the provisions of this subchapter must place an installation label on the system to certify that the system was installed in compliance with the manufacturer's installation manuals and specifications or standards adopted by the commissioner in this subchapter. The licensee whose signature appears on the installation label must be present for the final test of the system prior to certification.

(3) On completion of the installation of a fixed fire extinguisher system other than a pre-engineered system, a Type A or Type PL licensee must place an installation label on the system to certify that the system was installed in compliance with the manufacturer's installation manuals and specifications, plans developed by a Type PL licensee or professional engineer, or standards adopted by the commissioner in this subchapter. The licensee whose signature appears on the installation label must be present for the final test of the system prior to certification.

(4) A service tag certifying the work the licensee performed must be securely attached to the system on completion of the work.

(c) Pre-engineered fixed fire extinguisher systems must be installed and serviced by a licensee authorized to install or service pre-engineered fixed fire extinguishing systems under the provisions of this subchapter.

(d) A pre-engineered fixed fire extinguisher system, except those covered by subsection (f) of this section, which has been previously installed in one location may be reinstalled in another location if:

(1) the system is of the size and type necessary to protect all hazards;

(2) all parts and equipment, when installed, will function as designed by the manufacturer; and

(3) the system complies with all applicable adopted standards.

(e) Fixed fire extinguisher systems other than pre-engineered systems must be planned, installed, or serviced by a Type PL licensee or professional engineer. Installation and servicing of these systems may also be performed by or supervised by a Type A licensee. An employee of the registered firm may install these systems, under the direct supervision of a Type A or PL licensee, without obtaining a license or permit.

(f) All pre-engineered fixed fire extinguishing systems, installed or modified after July 1, 1996, according to NFPA 17 or NFPA 17A or NFPA 96 of the adopted standards for the protection of commercial cooking areas, must meet the minimum requirements of Underwriters Laboratories, Inc., Standard 300, "Fire Testing of Fire Extinguishing Systems for Protection of Restaurant Cooking Area" (UL 300). After January 1, 2008, all existing pre-engineered fixed fire extinguishing systems, installed in accordance with NFPA 17 or NFPA 17A or NFPA 96 of the adopted standards, for the protection of commercial cooking areas, must meet the minimum requirements of UL Standard 300, "Fire Testing of Fire Extinguishing Systems for Protection of Restaurant Cooking Area" (UL 300) or a red tag must be attached following the procedures in §34.521 of this title (relating to Red Tags).

(g) If the installation or servicing of a fixed fire extinguishing system includes the installation or servicing of any part of a fire alarm or detection system or a fire sprinkler system other than the installation and servicing of mechanical or pneumatic detection or actuation devices in connection with the fire extinguishing system, the licensing requirements of the appropriate Insurance Code Chapters 6002 or 6003 must be satisfied.

(h) The fixed-temperature sensing elements of the fusible metal alloy type, replaced while servicing a kitchen hood fire extinguishing system, must bear the manufacturer's date stamp, which must be within one year of the date of the replacement. The year of manufacture, temperature, and quantity for new fusible links must be listed on the service tag under service performed.

(i) The disposable actuation cartridge, replaced while servicing a kitchen hood fire extinguisher system, must bear the date of replacement.

(j) After operating the pull pin or locking device during maintenance of a portable fire extinguisher, the flag of the new tamper seal must bear the year it was attached. The date must be imprinted or embossed on the flag of the new tamper seal. Dates applied with a marker are not allowed.

(k) All pre-engineered dry chemical fixed fire extinguishing systems, installed in new, remodeled, or relocated protected areas after January 1, 2006, must meet the minimum requirements of the second edition (1996) or more recent edition of Underwriters Laboratories, Inc., Standard 1254, Pre-engineered Dry Chemical Extinguishing System Units.

Rule §34.518 - Fire Extinguisher Fixed System Plans for Other Than Pre-engineered Systems - (a) A set of shop drawings and hydraulic calculations showing details of system piping, calculations, and alarm configurations must be provided to the building owner or his representative when installation of a fixed extinguisher system protecting special hazards is complete. The firm must also maintain a set of shop drawings for the life of the system.

(b) Subsequent alterations or additions must be legibly noted on updated plans and provided to the owner. Additions to systems protecting previously unprotected hazards also require updated plans. Updated plans must be maintained by the firm for the life of the system.

(c) All shop drawings must bear the signature of a Type PL licensee, his license number, the date of installation, and the certificate-of-registration number of the registered firm.

(d) A rubber stamp may be used to supply the required information; however, a stamped signature is prohibited. If a rubber stamp is used, it shall produce an imprint 2 1/2 inches wide by one inch high, all in boldface type and capital letters and in the following sample format.

Attached Graphic

Rule §34.519 - Installation Labels for Fixed Extinguisher Systems - (a) After an installation has been completed, an installation label must be affixed to the control head or panel of the fixed fire extinguisher system. The signature of the licensee on the label certifies that the system has been installed according to law. Labels must be five inches in height and four inches in width and must be of the gum label type. They must not be red in color. Installation labels must contain only the following information in the format of the label shown in subsection (b) of this section:

(1) the inscription "DO NOT REMOVE BY ORDER OF THE STATE FIRE MARSHAL--SYSTEM INSTALLATION RECORD" (all in capital letters, at least 10-point boldface type);

(2) the firm's name, address, and telephone number;

(3) the firm's certificate-of-registration number;

(4) the signature and license number of the licensee authorized to certify a fixed fire extinguishing system (a stamped signature is prohibited);

(5) the date of installation; and

(6) identification of the manufacturer's manual(s) used for installation.

(b) Installation label:

Attached Graphic

(c) Certificate of Installation.

Attached Graphic

(d) After completion of the installation, modification, or addition of a fixed fire extinguisher system, the licensee must complete an installation certificate in the format provided by the state fire marshal (see Certificate of Installation). When an installation certificate has been completed, legible copies must be distributed as follows:

(1) original to owner or posted on site at control head or panel;

(2) a copy to main authority having jurisdiction, if required; and

(3) a copy to certifying firm to retain in their office for access by SFMO.

Rule §34.520 - Service Tags - 

(a) After any service, the licensee must complete a service tag in detail, indicating all work that done, and then attach the tag to the portable or fixed system in such a position as to permit convenient inspection and not hamper its actuation or operation. The signature of the licensee on the service tag certifies that the service performed complies with requirements of law.

(b) A new service tag, yellow tag or red tag, as applicable, must be attached each time service is performed.

(c) Service tags must bear the following information in the format of the tag shown in subsection (g) of this section:

(1) "DO NOT REMOVE BY ORDER OF THE STATE FIRE MARSHAL" (all capital letters, at least 10-point boldface type);

(2) firm's name, address, and telephone number;

(3) firm's certificate-of-registration number;

(4) licensee's name and license number;

(5) licensee's signature (a stamped signature is prohibited);

(6) month and year (to be punched);

(7) type of work (to be punched);

(8) service performed;

(9) name and address of owner or occupant; and

(10) extinguisher type, size, and location.

(d) Tags must be 5-1/4 inches in height and 2-5/8 inches in width. Service tags must not be red in color.

(e) Tags may be printed and established for any five-year period.

(f) A service tag may be removed only by an authorized employee of a registered firm, an employee of the state fire marshal's office, or an authorized representative of a governmental agency with regulatory authority.

(g) Service tag:

Attached Graphic

(h) Adhesive label type tags are permitted. The label must bear all information required by subsection (c) of this section.

Rule §34.521 - Red Tags - 

(a) If impairments exist that make a portable extinguisher or fixed system unsafe or inoperable, the owner or the owner's representative must be notified in writing of all impairments. The registered firm must notify the owner or the owner's representative immediately and must also notify the local authority having jurisdiction (AHJ) when available within 24 hours by phone, fax, or email describing the impairments or deficiencies. A copy of the written notice to the owner must be submitted to the AHJ within three business days. A completed red tag must be attached to indicate that corrective action or replacement is necessary. The signature of the licensee on the tag certifies that the impairments listed indicate that the equipment is unsafe or inoperable. A service tag must not be attached until the impairments have been corrected or the portable extinguisher or fixed system is replaced and the extinguisher or fire extinguisher system re-inspected and found to be in good operating condition. The local AHJ must be notified when corrections are made and a red tag is removed or revised. The notification must be postmarked, emailed, faxed, or hand delivered within five business days of the removal of the red tag.

(b) Red tags must be the same size as service tags.

(c) Red tags must bear the following information in the format of the tag shown in subsection (e) of this section:

(1) "DO NOT REMOVE--EQUIPMENT IMPAIRED" (all capital letters, at least 10-point boldface type);

(2) firm's name and address;

(3) firm's certificate-of-registration number;

(4) licensee's name and license number;

(5) licensee's signature (a stamped signature is prohibited);

(6) date;

(7) list of impairments; and

(8) name and address of owner or occupant.

(d) A red tag may be removed only by an authorized employee of a registered firm who has corrected the impairments and certified the service, an employee of the State Fire Marshal's Office, or an employee of another governmental agency with regulatory authority.

(e) Red tag:

Attached Graphic

Rule §34.522 - Severability - If any provision of this subchapter or the application thereof to any person or circumstance is held invalid for any reason, the invalidity shall not affect the other provisions or any other application of this subchapter which can be given effect without the invalid provisions or application. To this end, all provisions of this subchapter are declared to be severable.

Rule §34.523 - Savings Clause - Each cause of action, pending litigation, matter in process before the commissioner or the state fire marshal, or matter hereafter arising from an event occurring prior to the time this subchapter becomes effective shall be determined in accordance with and governed by the provisions of statutes, sections, orders, or official interpretations in effect at the time of the occurrence of the subject event.